Telecom products

30 voice FXO/FXS E&M RS232 ethernet E1 over fiber PCM multiplexer:PCM-F30

Introduce

PCM-F30 is the point-to-point optical transport equipment that uses the FPGA chips. It is single board structure and provided with complete alarming function. It provides 1~4 10/100M Ethernet channels, 1~30 voice (FXS/FXO) channels and 1~4 serial data channels,4E1 for option. It can realize SNMP management on stand-alone device via built-in SNMP module. The outer design use the standard 19 inches rack, so the volume is small, weight is light and operation is convenient and credit.

Features

 01.Base on IC of independence intellectual property rights.
02.Adopt veneer structure.
03.Offer 1~4 ×2Mb/s digital interfaces.
04.Provide 1~4 channels of 10M/100M, support VLAN setting.
05.Provide 2 extensional ports that can extend various data channels, such as asynchronous data(RS232/RS485/RS422/Manchester), switching value, E1, voice or 2/4-wire audio.
06.Provide 1~30 voice channels, supporting FXS/FXO.
07.When fiber signal is loss, users can distinguish whether the remote device is power off or the fiber line is down from the

indicator status on the local device.

08.1U/19inch type model can provide SNMP network management port independently. It can also support cascade

management. (optional).
09.User can become conscious of the temperature and voltage of the local device in SNMP managing interface. (Optional).
10.User can also become conscious of the temperature and voltage of the remote device in SNMP managing interface, and

can set the alarm threshold of the remote device’s temperature. (Optional).
11.180-260VAC & -48VDC power options and the positive and negative of DC-48V can be optional because there is the self

-test circuit for the polarity inside th1e device.
12.Standard 19 inches rack, little volume, light weight, steady capacity and convenient setup.

Specification
Fiber interface
Optical wavelength:1310nm/1550nm(single-mode)
850nm/1310nm(multi-mode) for option
Optical interface:SC/FC/ST for option
Sending consumption: -9dBm/-5dBm
Receiving and dispatching module:>-6dBm
Optical receiver receiving sensitivity<-36 (BER<10):
Optical code:NRZ
Transmitting range: MM0~2Km; SM 0~120Km for option

E1 interface
Interface code:HDB3 code
Line speed:2.048Mbp/s ±50ppm
Interface standard:ITU-T G 703
Interface impedance:75Ω/unbalanced (BNC)
Allowed attenuation:0~6dBm

FXS Telephone Port
Ring voltage: 75V
Ring frequency:25HZ
2 line input impedance:600Ω (hanging off)
Wastage: 40db

FXO Exchange Port
Ring detecting voltage:35V
Ring detecting frequency:17HZ-60HZ
2 line input impedance: 600Ω (hanging off)
Wastage:40db

2/4 wire E&M interface card  
Channel quantity per card: 2 
Standard referred to: ITU-TRECG.714
Transmit relative level: +3,0, -3dBr adjustable
Receive relative level: +3,0, +3dBr adjustable
Signaling mode: E&M
Interface impedance: 600Ω
Subscriber physical connector: RJ45

10/100Base-T Port
Rate:0/100M, full/duplex auto-negotiation
Protocol:Support IEEE 802.3, IEEE 802.1Q (VLAN)
MACAddress Entiries:4096Entiries
Connector:RJ45

RS232/Console port
Rate:600Kbps (Asynchronous)
Interface characteristic：  satisfies ITU-T V.24 standard
Connector：            RJ45

Dimension
485 mm(L)*250 mm(W)*43mm(H)

Power supply
AC220V:input voltage AC 180V～260V
DC-48V:input voltage -36V～-72V

Operation Condition
Voltage:AC180V ~ 260V; DC –48V; DC +24V
Consumption:≤5W
Operating temperature:0°C~50°C
Storing temperature:40°C~+70°C
Relative humidity:95 %

Typical Application

PDH Multiplexer
SDH Multiplexer
E1 Converter
TDM over IP
Modem
PCM Multiplexer
Fiber Media Converter
Fiber Video Converter
Fiber Module
SFP Fiber Module
SFP+ Fiber Module
40G 100G Module

PCM Multiplexer
Fiber Module
SFP+ Fiber Module
40G Module
100G Transceiver
Fiber to Ethernet Converter
E3 DS3 to Ethernet Converter
Fiber Optical Modem
TDM over IP
G.SHDSL Modem

Ultra Low Temperature Freezer
Speed Reducer
Rehabilitation Equipment
Telecom Equipment