GSDSL:2 Wire G.SHDSL Modem hdsl E1 V.35 modem
2 Wire back to back modem
G.SHDSL Modem
HDSL XDSL modem
E1 V.35 modem
extend E1 line
2 Wire back to back modem
G.SHDSL Modem
HDSL XDSL modem
E1 V.35 modem
extend E1 line
2 Wire G.SHDSL Modem hdsl E1 V.35 modem:GSDSL
Description
2.3Mbps,2-Wire,G.SHDSL Modem
Introduce
Features
To use ITU G.shdsl standard 2-wire 2304Kbps GSDSL modem
3.5km-9.7km transmitting distance in special lines with 24AWG(0.5mm) and 26 AWG(0.4mm)
Optional digital interface: V.35 and G.703, Rate support :N*64Kbps(3<=N<=36), 2304Kbps can be reached highest
Need not setup rate of slave modem, It follows the speed rate master modem automatically. So it is carried out to administrate the remote equipments in networks
There are many indicator LEDs on the panel to display work state and line of equipment
High-powered 2B1Qline coding technology is used
Low operating cost, simple manipulation, convenient use, need not any software setting up
The test of analog loopback and digital loopback will be finished by keys of front panel
Independent machine have two power supplying modes: alternating current and direct current-48V
Overview
GSDSL is FPGA-based 2-wire 2304Kbps modem. According with ITU G.SHDSL standard, with best concocting technology and very good frequency spectrum compatibility. It can be used in every high-grade and high-speed telecom operation such as transmitting voice, data and images.
GSDSL has strong supervisory control function. You can learn from the panel the start-up, running and line malfunctioning and so on. When the system is malfunctioning, one can locate the fault expediently with loop back test to administrate networks.
One can use the DIP switch on the back panel to setup work mode and transmission rate while slave modem can automatically follow master modem rate (that is the rate switch of the slave need not to work). So you can administrate the remote equipments in networks.
Specifications
Line interface
Fully conforming to standard of YDN 056-1997
Transmission rate: |
N*64Kbps+8Kbps(N=3~36) |
Code: |
PAM16 |
Line impedance: |
135ohm |
Signal electrical level: |
+13.5 +/- 0.5dbm |
Line wire interface: |
a pair of passive twisted-line, RJ45 |
Code error rate: |
<=10 -9 |
Transmission distance without linkup: |
3.5~9.7Km(0.4~0.8mm wire size) |
Data interface 1 (E1 interface)
Transmission rate: |
N * 64Kbps(N=1~32) |
Line coding: |
HDB3 |
Line impedance: |
75ohm/120ohm |
Interface standard: |
according with CCITT G.703 standard |
Data interface 2 (V.35 /V.24)
Transmission rate: |
N *64Kbps(N=3~36);V24(64K; 128K;) |
Work mode: |
DCE |
Work circumstances
Power supply: |
220VAC+/-10%,50Hz;48VDC(optional) |
Power consumption: |
<5W |
Volume: |
245mm*215mm*50mm 9"L*5.8"W*1.6"H |
|
|
Temperature:
Relative humidity: |
0oC~ +40oC
0~95% |
Typical Application:
PDH Multiplexer
SDH Multiplexer
E1 Converter
TDM over IP
Modem
PCM Multiplexer
Fiber Media Converter
Fiber Video Converter
fiber module
SFP fiber module
SFP+ fiber module
40G 100G module
PCM multiplexer
fiber Module
SFP+ fiber module
40G module
100G transceiver
fiber to ethernet converter
E3 DS3 to ethernet converter
fiber optical modem
TDM over IP
G.SHDSL modem
Ultra Low Temperature Freezer
Speed Reducer
Rehabilitation Equipment
Telecom Equipment