Email:   sales@fastfom.com

cenny.xu@hotmail.com

Skype ID:cenny.xu

 

  • cenny.xu@hotmail.com-Click To Talk
  • cenny.xu-Click To Talk

TOIP-1E1:one E1 TDM over IP 10/100M user ports


one E1 TDM over IP 10/100M user ports

More details


TOIP-1E1:one E1 TDM over IP 10/100M user ports

Description
 
E1 Over Ethernet Multiplexer (1*E1)
 
Introduce

TOIP-1E1 is mainly used to transmit voice signal over IP network. It has 1 E1 interface, 1 local Ethernet port and 2 uplink Ethernet ports. TDMoIP can connect TDM device and user’s Ethernet seamlessly and reliably on the standard low cost wireless or lineate Ethernet/IP configuration, without affecting the voice quantity. Being transparent to the TDM signal, thismodel assures connecting to physical E1 interface of any device seamlessly, such as PBX, mobile base station, SS7 signaling device and voice mail system. It can be used in the communication system based on E1, such as LAN, WAN, MAN and wireless network.

   Providing emulation E1 channel through Ethernet, the difficulty is rebuilding timing information of E1 code stream effectively at the exit of network. The special disadvantages of Ethernet itself, such as random packet delay, without effective timing transmit mechanism, transmission error or collision that brings on packet lose, must be conquered. Our company resolves the difficulties above faultlessly through availing ourselves of technical advantage and adapting advanced clock disposal technology. TDMoIP encapsulates the date of E1 code stream to the packet and transmits it to the remote device through Ethernet. This model has two method of encapsulation for optional: Ethernet encapsulation simplicity and UDP/IP protocol encapsulation. The former is suit for the connection of the same Ethernet subnet, because it has high encapsulation efficient especially suited to the occasion of bandwidth intensity, such as interconnection based on the wireless network bridge.  But it can’t span router. The latter is suit for the inner net connection of IP net, with the advantage of making use of router or 3-layer switch. But the disadvantage is that the addition IP header needs extra bandwidth. When adapting 128B encapsulation, each E1 channel will take up 500kbps more than Ethernet encapsulation simplicity, with lower transmission efficiency. User can select different encapsulation type based on practical usage occasions.   

   
Characteristics
01.Transmit framing, non-framing and complex-framing E1(N*64K)signal Transparently, confirming to ITU-G.703.
02.High transmit efficiency, low transmit delay.
03.Provide 1 E1 channels and 1 10/100Base-TX downlink ports with universal RJ45 Ethernet interface, 10M/100M auto-adapt.
04.The length of Ethernet packet can be set, supporting long packet.
05.User can select IP protocol encapsulation or simplicity Ethernet type.
06.Support VLAN setting.
07.Support ETH ping function.
08.Support package loss indicator function for E1 transmission line.
09.Local and remote E1 loop and local E1 enable function.
10.Point to point or point to multi-points connections, satisfying different applications.
11.High efficiency transmission, up to 90% bandwidth utility ratio.
12.Support two type interfaces-75Ω and 120Ω-unneed setting.
13.10/100M Ethernet, full/half duplex auto-adapt, support auto-MDIX.
14.When selecting network adaptation clock, it can resume the original clock accurately through TDM clock resumption
mechanism, stable clock, little jitter and small excursion, conforming to ITU-T clock jitter and excursion standard.

Parameter and index
(1) E1 interface
Standard:      conform to G.703 standard
Code rate:     2.048Mbit/s±50ppm
Code type:     HDB3       
Impendence:   75Ω(unbalance)/ 120Ω(balance)
Connector:     BNC(unbalance)/ RJ45(balance)
Jitter tolerance:  conform to G.742 and G.823 

(2) 10/100Base-T port
Rate:       10/100M, full/half duplex auto-adapt
Protocol:     support IEEE 802.3, IEEE 802.1Q (VLAN)
MAC address table:    1024 MAC addresses
Physical connector:    RJ45, support AUTO-MDIX

Working condition
Voltage:    AC180V ~ 260V, DC –48V, DC +24V
Power Consumption:     ≤5W
Working temperature:    0°C~50°C
Storage temperature:     -40°C~+70°C
Relative humidity:       95%
No causticity and solvent, dust free and no strong magnetic interference.

Dimensions
483mm×138mm×44mm
212mm×138mm×30mm

 

Typical Application

/img/TOIP-1-2.jpg

E1 TDMOIP

 

TDM over IP

one E1 TDM over IP

1E1 over IP

2E1 TDM over IP

2E1 TDMOIP

4E1s TDM over IP

8E1 TOIP

16 E1 TDM over IP

 

 

 

 

 

 

PDH Multiplexer
SDH Multiplexer
E1 Converter
TDM over IP
Modem
PCM Multiplexer
Fiber Media Converter
Fiber Video Converter
Fiber Module
SFP Fiber Module
SFP+ Fiber Module
40G 100G Module

PCM Multiplexer
Fiber Module
SFP+ Fiber Module
40G Module
100G Transceiver
Fiber to Ethernet Converter
E3 DS3 to Ethernet Converter
Fiber Optical Modem
TDM over IP
G.SHDSL Modem

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Ultra Low Temperature Freezer
Speed Reducer
Rehabilitation Equipment
Telecom Equipment